Agrimensores

View as List Grid

Items 1-10 of 25

Page
por página
Set Descending Direction
  1. 2T - Nuevas Tecnologías e Innovación para Agrimensores
    $30.00

    En este curso de dos (2) horas, aprenderá las últimas tecnologías en el campo de la agrimensura. La tecnología de agrimensura evoluciona con más rapidez de lo que podemos asimilar. Resulta esencial estar al día para no quedar rezagados. En este curso, los ingenieros y agrimensores aprenderán sobre los cambios en la recopilación de datos. Hoy día, los ingenieros y agrimensores trabajan con datos en tres dimensiones. La nueva tecnología hace que los datos de topografía sean más naturales para capturar y revisar de inmediato.

    Horas Contacto: Dos (2) horas técnicas

    Learn More
  2. 3T - Repairs & Alterations to Existing Infrastructure - a Systems Project Management Approach
    $50.00

    A building repair and restoration model based on the project management strategy is presented. This project management strategy will structure a project repair and alterations delivery aligned with building code and regulations as determined by SME team. The proposed building repair solution will include an approved:  scope of work, schedule, and budget.

    Learn More
  3. 2T - Shunt Capacitor Bank Design and Protection Basics
    $30.00

    This course is suitable for electrical engineers with a desire to understand the fundamentals of capacitor units’ operation and associated protection principles. Presented information cover issues related to technical implementation and exploitation of capacitor bank systems. Upon successful completion engineers will be able to address different capacitor bank systems, configurations and their protection schemes.

    Contact Hours: 2 Hours - Technical

    Learn More
  4. 3T - Introduction to Motor Starting Analysis
    $50.00

    The starting current of most AC motors is several times normal full load current. Both synchronous and induction motors can draw five to ten times full load current when starting them across the line. Motor-starting torque varies directly as the square of the applied voltage. If the terminal voltage drop is excessive, the motor may not have enough starting torque to accelerate up to running speed. Running motors may stall from excessive voltage drops, or under-voltage relays may operate. In addition, if the motors are started frequently, the voltage dip at the source may cause objectionable flicker in the lighting system.

    Contact Hours: 3 Hours - Technical

    Learn More
  5. 2T - Wind Energy Project Analysis
    $30.00

    In addition to large scale applications, there are a number of other applications for wind turbines, such as medium scale applications on isolated-grids and off-grid uses for pumping water and providing smaller amounts of electricity for stand-alone battery charging applications.

    Contact Hours: 2 Hours - Technical

    Learn More
  6. 4T - Introduction to Short Circuit Current Calculations
    $60.00

    This course presents the subject of short-circuit studies in a very structured fashion. First, a simple equivalent circuit is developed for a generic power system, system impedances are recalculated to common base and fault are calculated at various locations throughout the system. A detailed explanation is offered for calculation of three phase faults. Explained techniques can be also verified by any commercial power system software package.

    Contact Hours: 4 Hours - Technical

    Learn More
  7. 3T - Distance Protection
    $50.00

    Since the impedance of a transmission circuit is relative to its length, for distance measure it is suitable to use a relay able to measure the impedance of a circuit up to a present point (the reach point). Such a protection relay is known as a distance protection relay and is made to function only for faults happening between the protection relay location and the chosen reach point, therefore providing discrimination for short circuits that may happen in different line portions.

    Contact Hours: 3 Hours - Technical

    Learn More
  8. 3T - Análisis forense de atraso según prácticas recomendadas de la industria de la construcción (AACE)
    $50.00

    El análisis forense de retrasos programados es el estudio e investigación de eventos que utilizan los métodos de programación de CPM para establecer la causa y el alcance de los retrasos y para resolver reclamos de retrasos en la construcción a través de negociaciones o procedimientos legales. Es un campo para expertos entrenados y con experiencia en la programación de CPM.

    Horas de Contacto: Tres (3) horas

    Learn More
  9. 3T - Manejo de Reportes y Utilidades para Puntos y Superficies en AutoCAD Civil 3D 2017
    Special Price $50.00 Regular Price $75.00

    Este curso está orientado a brindar a los participantes el conocimiento necesario para ejecutar los diferentes tipos de reportes que ofrecer el programa de AutoCAD Civil 3D, al momento de manejar puntos Cogo y Superficies. De esta forma se puede optimizar el trabajo y presentar la información de los proyectos de manera estética.

    Horas de contacto: Tres (3) horas técnicas

    Learn More
  10. 3T - "GIS for Rookies"
    $75.00

    Curso introductorio que discute el uso del GIS, al finalizar el curso el participante entenderá cómo funciona el GIS y que operaciones se pueden realizar con la aplicación.

    Learn More
View as List Grid

Items 1-10 of 25

Page
por página
Set Descending Direction